inflatable boat

Inflatable boats, kayaks, accessories and products for inflatable boats, accessories for powerboats, sailboats yachts, and more.


A to Z PRODUCT MENU

Arches, Frames, Towers
Apparel
Boats
Bouncer Trampolines
Canoes - Inflatable
Consoles
Covers - Inflatables
Davits - Inflatable Boat
Dinghies
Dinghy Davits
Dinghy Launch Wheels
Engine Covers
Engine Brackets
Engine Carry Cases
Engine Jack Plates
Engine Mounts
Inflatable Bouncers
Inflatable Boats
Inflatable Canoes
Inflatable Kayaks
Inflatable Boat Davits
Inflatable Boat Paint
Inflatable Boat Parts
Inflatable Boat Sealant
Inflatable Seating
Inflatable Storage Bags
Inflatable Tow Sleds
Inflatable Towables
Inflatable Trampolines
Jack Plates
Kayaks
Keel Guard Strips
Launching Wheels
Lights
Motor Carry Cases
Motor Covers
Motor Mount Brackets
Outboard Cases
Outboard Covers
Outboard Motor Mounts
Paint - Inflatable Repair
Planing Fins
Propeller Guards
Repair Paint Inflatables
Rigid Inflatable Boats
Sealant for Inflatables
Seating & Consoles
Steering Systems
Stabilizers for Engines
Storage Bags
Tilt Trim Systems
Tenders for Yachts
Towables - Inflatables
Trampolines
Trim Tab Lights
Wakeboard Racks
Wakeboard Speakers
Wakeboard Towers
Water Bouncers
Water Sleds
Yacht Tenders

 

SeaEagle.com - Quality Inflatable Boats

 

 


November 11, 2003
Website: http://www.inflatable-boats-kayaks-accessories.com

Inflatable boat repairs tips and repairing information

You can easily repair your inflatable boat and its minor punctures (1cm or less), be it either in Hypalon or in Strongan/PVC fabric. Read basic repair instructions below, but when performing simple repairs follow the instructions in your owner's manual. Always use safety equipment. Seek a professional repair station for complete details, instructions and materials.
For larger repairs, consult your authorized dealer.

To know the fabric of your inflatable boat, check the buoyancy tube’s vertical seams. Since about 1985, most ZODIAC boats are made in Strongan/PVC fabric.

HAND-GLUED SEAMS = HYPALON FABRIC
Traditional assembly method for hypalon fabric. The 2 panels are glued, one covering the other. You will only see part of fabric that covers the other section.

THERMOBONDED SEAMS = STRONGAN FABRIC
Robotized hot assembly technique: two layers of fabric are welded between an exterior reinforcement band and an interior airtight band. What you see is the exterior band, with 2 borders.
 
REPAIR KIT
Cleaning:
- Hypalon fabric: rough the material with the pumice stone provided (never use solvent)
- Strongan fabric: Grease remover of the MEK or acetone type. Use safety equipment.
Repairing:
- Fabric patch (use correct fabric for your boat)
- Tube of special glue, ready for use: check with your dealer that you use the suitable glue
- Small paint brush

CONDITIONS NECESSARY FOR A SUCCESSFUL REPAIR
- Relative humidity less that 60%
- Temperature between 18 and 25°C (64.4 and 77°F)
- Avoid carrying out repairs in direct sunlight or rain
- Check that the buoyancy tube is fully deflated and lies flat

PREPARATION
- Cut out a round patch at least 5 cm larger than the hole or cut to be repaired
- Draw around the shape of the patch exactly where it will be applied on the boat
- Clean the damaged part of the boat and the corresponding side of the patch
- Strongan fabric: with a grease remover of the alcohol type
- Hypalon fabric: with the pumice stone only
- Allow to dry for 5 minutes

GLUING
- Apply 3 thin layers of glue on both the patch and the roughened area on the boat and let dry for 5 to 10 minutes between each layer until tacky

PUTTING ON THE PATCH
- When the 3rd layer is dry, apply the patch without pressing and adjust the position if required
- Press out the air bubbles which may have formed under the patch
- Smooth the patch with a round object (ie: a spoon) starting from the center of the patch and working out
- Clean the excess glue with a solvent

USE OF BOAT AFTER REPAIR
- Do not expose the repair to sun or rain until cured
- Let dry and cure for 24 hours before inflating
 
CAUTION !
When using the glue :
- Carefully replace the cap on the tube of glue. If properly sealed, it keeps well.
- Do not leave the tube in the sun or next to heat sources or direct flames.
- Check that the room is properly ventilated, avoid inhaling or ingesting the glue, and avoid its contact with your skin
 

NOTE: FOR MAJOR REPAIRS, TAKE YOUR BOAT TO AN AUTHORIZED DEALER WHO CAN PERFORM AFTER SALES SERVIC.

 

About The Author:
T. Chevrier is a successful author and publisher of several online articles in the inflatable boat industry for
www.inflatable-boats-kayaks-accessories.com


 

Follow us on:
Twitter
Facebook
YouTube

Featured Boat Product
SeaEagle.com


Related Information


SUPPLIERS & MANUFACTURERS
Add your products to our site?



Great Products +
Low Prices +
Great Service =
An enjoyable buying experience and savings
for you



Customer Services


E-mail Us
Your Questions:
E-mail us Now

Call Toll Free at:

1-888-309-0990

Join Our
Mailing List
E-mail us Now



Related Websites

Allinflatables
A name you can trust

All Boat Products
A wide variety

Custom Motorcycle Products
Lots of info and parts


Sea Eagle Sport Runabout Transom Boat 

Copyright - All Rights Reserved

www.allboatproducts.com www.allboatinfo.com www.allwatersportsproducts.com www.allinflatables.com www.allwakeboardproducts.com www.inflatableboats.ca www.cultuslakecottagerentals.com www.custommotorcycleproducts.com www.militaryboats.com